ferrotip.blogg.se

FIRMWARE UPDATE FOR BCR 2000 HOW TO
FIRMWARE UPDATE FOR BCR 2000 ZIP FILE
FIRMWARE UPDATE FOR BCR 2000 FULL
FIRMWARE UPDATE FOR BCR 2000 SOFTWARE

Your BCF2000 is now ready to control Ardour! Source: 10.2. You can cancel the store operation at any time by pressing EXIT. If you want to overwrite an existing preset, press STORE twice. Press STORE again to write the settings to an empty preset. Select a different preset number if you wish with the left and right PRESET buttons. The CC values for the first row of buttons run from 65 to 72, and from 73 to 80 for the second row.įinally, you need to store these changes so that they'll be kept even when the BCF has its power cycled. The steps are the same for the two rows of pushbuttons under the rotary knobs.

This will set the CC parameter for the second knob to 34, the third knob to 35, and so on.

Turn the rotary control labeled MODE until the display reads t on.Ĭontinue to program the other rotary controls in the same way, incrementing the value set by the PAR control by 1 each time.

Turn the rotary control labeled PAR until the display reads 33.

Turn the rotary control labeled TYPE until the display reads CC.

Hold down the EDIT button and press the rotary control.

Here's a quick walk through to program the controls on the BCF.

Second row of buttons: CC73 through CC80.

First row of buttons: CC65 through CC72.

Rotary knobs 1 through 8 when pressed: CC33 through CC40.

Here's a list of the controls and what they should send: This required re-programming the BCF a bit. This was because in P2, the buttons sent a Program Change signal, but Ardour expects a Control Change signal. Preset 2 (P2), the Simple Mixer, is almost there, but the mute, solo and rec-enable controls in Ardour can't be mapped to a pushbutton on the BCF.

Let's prepare it for a modest set of things to the BCF to control for a track: Customizing your control surfaceīC control surfaces require some customization to be used with Ardour.

FIRMWARE UPDATE FOR BCR 2000 HOW TO

If that's not on, you'll need to figure out how to make your USB port work under Linux. When you connect your device to your computer you should see the BCF's USB MODE light come on in the upper right corner. You should then see the version number of the upgraded firmware displayed for a few seconds as the BC starts. Once the whirling stops, you should turn off the BC, count to 5, then turn it on again. The BC display will show a whirling figure-8 animation and count up to 18.

FIRMWARE UPDATE FOR BCR 2000 SOFTWARE

Make sure you use the actual device you determined in the previous step The total-recall B-CONTROL BCR2000 USB/MIDI Controller combines the unlimited versatility of todays audio software with the feel of real handson controls. Write the firmware to the BC with the command The BC is almost certain, then, to use the device /dev/snd/midiCnD0 where n is the card number, in this case, 2. The number at the left indicates the card number.

FIRMWARE UPDATE FOR BCR 2000 FULL

Choose the appropriate one.īEHRINGER BCF2000 at usb-00:1d.1-2, full speed You'll typically extract 2 SYX files, one for the BCF 2000 and the other for the BCR 2000. There may be a newer version available now.) (This example uses version 1.10 of the firmware, the latest available at the time of this writing.

FIRMWARE UPDATE FOR BCR 2000 ZIP FILE

There will be a zip file available which should be downloaded. This is a relatively painless process.ĭownload the firmware from Downloads tab at BCF 2000's page.

The first thing you're likely to have to do is update the firmware in the unit. There are a few steps to prepare the BC2000 to work with Ardour. Is this how the BCR is supposed to look when it starts up? I never actually used the original firmware before installing the ZAQ, so I'm unsure.This page presents specific info about BCF 2000 and BCR 2000 control surfaces that should be taken in consideration when following Improved Mackie/Logic Control Support page intructions. In that case I can at least assign encoders to functions in live, but there are some odd habits (like the 24th encoder going all the way to 9999 instead of 127.) I can sort of get it to work in live by doing a dump from Live's midi preferences setting, but that gives me an Error 22 once it's all done. But none of the encoders or lights anywhere on the device light up - Shouldn't the encoders all be set to one by default with the red LED light at the far left position? I can also scroll through presets, but each time I move up I get an "INIT" message. It turns on, flashes 1.10, then goes to P - 1 on the title page. Problem is, once I reset (using a sysex dump in midi ox) I don't believe the new base firmware is properly functional. I've been using my BCR2000 with the Zaquencer firmware for a while and planned to reinstall the original firmware to use it that way for a bit.